sdi2

(Return to Conductivity Sensors)

Model CS10 & 51 Conductivity Sensor
Click on part number above to request an RFQ or place an order online.

Small size enables convenient installation and service.
O-ring seals used on all versions for high on-stream reliability.
Plastic gland fitting allows removal and replacement without tools.
Wetted materials of construction are 316 stainless steel and Teflon, with double o-ring seals at all points. The outer EPR o-ring bears the brunt of process interface, allowing the back o-ring to maintain reliable sealing free from chemical attack. An integral temperature element, tailored to the analyzer of choice, allows automatic compensation for maximum accuracy. Leads are 10' standard, terminated in spade lugs.
Process connections are made via a bored through swage fitting with 1/2" or 3/4" NPT threads. This fitting can be screwed into a line, or tank, and it can also be turned around and connected to a standpipe for use in a submersion configuration. The CS51 is good for general purpose use up to about 20,000 micromhos on most analyzers, while the CS10 was designed primarily for use in pure water streams at low conductvities.

SPECIFICATIONS
MAX. PRESSUREITEMP. RATINGS:
100 PSIG at 1 OO°C
200 PSIG at 120°C w/316SS FITTING
CONNECTIONS:
Polypropylene Process Fitting - 1/2" or 3/4" NPT Stainless Steel Process Fitting - 1/2" NPT
Electrical - Spade lug terminations on cable.
WETTED MATERIALS:
Insulator - Teflon O-rings - EPR Electrodes - 316SS Standard Fitting - Polypropylene, 316SS Optional.
PROBE CONSTANT:
CS10 - 0.1/0.05/0.02
CS51 - 1.0/0.1
TEMPERATURE COMPENSATION:
Standard element is 10KΩ P 25°C, for use with SDI, Uniloc, Myron L, Sensor Technology, Signet, ECD and others. Other TC's available by specifying instrument make and model.

(Return to Conductivity Sensors)
	Model CS10 & 51 Conductivity Sensor Click on part number above to request an RFQ or place an order online. Small size enables convenient installation and service. O-ring seals used on all versions for high on-stream reliability. Plastic gland fitting allows removal and replacement without tools. Wetted materials of construction are 316 stainless steel and Teflon, with double o-ring seals at all points. The outer EPR o-ring bears the brunt of process interface, allowing the back o-ring to maintain reliable sealing free from chemical attack. An integral temperature element, tailored to the analyzer of choice, allows automatic compensation for maximum accuracy. Leads are 10' standard, terminated in spade lugs. Process connections are made via a bored through swage fitting with 1/2" or 3/4" NPT threads. This fitting can be screwed into a line, or tank, and it can also be turned around and connected to a standpipe for use in a submersion configuration. The CS51 is good for general purpose use up to about 20,000 micromhos on most analyzers, while the CS10 was designed primarily for use in pure water streams at low conductvities.
SPECIFICATIONS MAX. PRESSUREITEMP. RATINGS: 100 PSIG at 1 OO°C 200 PSIG at 120°C w/316SS FITTING CONNECTIONS: Polypropylene Process Fitting - 1/2" or 3/4" NPT Stainless Steel Process Fitting - 1/2" NPT Electrical - Spade lug terminations on cable. WETTED MATERIALS: Insulator - Teflon O-rings - EPR Electrodes - 316SS Standard Fitting - Polypropylene, 316SS Optional. PROBE CONSTANT: CS10 - 0.1/0.05/0.02 CS51 - 1.0/0.1 TEMPERATURE COMPENSATION: Standard element is 10KΩ P 25°C, for use with SDI, Uniloc, Myron L, Sensor Technology, Signet, ECD and others. Other TC's available by specifying instrument make and model.